Graco GG4615 Spray Tip - Aftermarket Replacement | Bedford 33-14615

Air-assist airless flat tip for dependable edge quality and film build on fine-finish jobs. This aftermarket tip replaces OEM GG4615 and is listed by Bedford as 33-14615, delivering a 0.015" orifice with a 12–14" fan for cabinetry, furniture, and light metal components.

Aftermarket 0.015" Orifice Industrial Duty

Why Choose This Spray Tip

  • Pre-orifice AAA design promotes soft atomization at modest pressures.
  • 12–14" fan helps cover panels and doors with fewer passes.
  • Direct interchange with the OEM code for quick booth changeovers.

Colour cue: Tip/guard colour bands aid quick ID on the rack; exact shade may vary by lot.

Typical Compatibility

  • Graco G15 manual air-assist airless guns.
  • Graco G40 manual AAA guns.
  • Graco G40 automatic AAA guns used on conveyors or fixtures.
  • Any AAA package whose IPL specifies the flat tip marked GG4-615 / GG4615.

Always confirm by part number in your gun/system IPL before ordering.

What This Product Fits

  • Graco G15 air-assist airless spray guns.
  • Graco G40 manual air-assist airless spray guns.
  • Graco G40 automatic air-assist airless spray guns on production lines.

Listed by Bedford as the aftermarket replacement for the OEM tip indicated above.

Technical Specifications

Aftermarket Bedford 33-14615
OEM Graco GG4615 (also GG4-615)
FitsGraco G15/G40 AAA guns (manual & automatic) when GG4615 is specified
TypeAir-Assist Airless flat spray tip (pre-orifice)
MaterialTungsten-carbide orifice with stainless components (typical AAA build)
FunctionDelivers soft, even patterns with clean edges for fine finishes
PressureUse within the gun/system rated working pressure
BrandAftermarket by Bedford Precision Parts; replaces Graco OEM

Code “615” ≈ 12–14" fan with ~0.015" orifice in the GG flat-tip family.

Installation Notes

  1. Relieve pressure and perform booth lockout/tagout.
  2. Inspect guard and aircap; clean with approved solvent only.
  3. Insert the tip with code facing forward; align fan to part geometry.
  4. Set assist air first for atomization, then trim fluid pressure.
  5. Spray a test panel and record settings for repeatable results.

Real Installation Tip: If tails appear, increase assist air slightly before raising fluid pressure.

When to Rebuild / Replace

  • Fan narrows or edges fuzz at normal standoff.
  • Higher fluid pressure needed to maintain target film build.
  • Pattern drifts off-center after verifying guard/aircap alignment.
  • Frequent clogs despite correct filtration and viscosity.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (33-14615)OEM (Graco)
InterchangeListed replacement for GG4615Factory original GG4615
Pattern / Orifice12–14" fan; ~0.015" orifice12–14" fan; ~0.015" orifice
Use CaseCabinetry, furniture, light metal finishingCabinetry, furniture, light metal finishing
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution

FAQs

Approximately 12–14" fan with ~0.015" orifice on AAA guns—ideal for controlled fine finishes.
Yes—this GG-series flat tip is specified for Graco G15/G40 manual guns and G40 automatic models where the IPL lists GG4615.
Bedford identifies 33-14615 as the replacement for the OEM reference shown above.
Dial assist air first, set a consistent spray height, and only increase fluid pressure if edges remain soft after air adjustment.
If available, orders ship from Bedford Precision Parts in Bedford Hill, NY using your selected carrier/service.