Graco GG4413 Spray Tip - Aftermarket Replacement | Bedford 33-14413

Air-assist airless flat tip for steady edge quality and transfer efficiency in fine-finish work. This aftermarket tip replaces OEM GG4413 and is referenced by Bedford as 33-14413, providing a ~0.013" orifice with an 8–10" fan for cabinetry, furniture, and light metal finishing.

Aftermarket 0.013" Orifice Industrial Duty

Why Choose This Spray Tip

  • AAA pre-orifice design promotes soft atomization at lower fluid pressures.
  • 8–10" fan width supports clean edges on doors, frames, fixtures, and casework.
  • Direct interchange with the OEM code for fast changeovers in the booth.

Colour cue: Tip/guard colour bands aid quick identification; marking style may vary by lot.

Typical Compatibility

  • Graco G15 manual AAA guns.
  • Graco G40 manual AAA guns.
  • Graco G40 automatic AAA guns used on conveyors or robots.
  • Any AAA package whose IPL specifies the GG4-413 (GG4413) flat tip.

Always confirm by part number in your gun/system IPL before ordering.

What This Product Fits

  • Graco G15 air-assist airless spray guns.
  • Graco G40 manual air-assist airless spray guns.
  • Graco G40 automatic air-assist airless spray guns on production lines.

Listed by Bedford as the aftermarket replacement for the OEM tip indicated above.

Technical Specifications

Aftermarket Bedford 33-14413
OEM Graco GG4413 (also GG4-413)
FitsGraco G15/G40 AAA guns (manual & automatic) when GG4413 is specified
TypeAir-Assist Airless flat spray tip (pre-orifice)
MaterialTungsten-carbide orifice with stainless components (typical AAA build)
FunctionDelivers soft, even patterns at modest pressures for fine finishes
PressureUse within the gun/system rated working pressure
BrandAftermarket by Bedford Precision Parts; replaces Graco OEM

Code “413” ≈ 8–10" fan with ~0.013" orifice in the GG flat-tip family.

Installation Notes

  1. Relieve system pressure and follow booth lockout procedure.
  2. Inspect guard and aircap; clean with approved solvent only.
  3. Insert the tip with code facing forward; align fan to part geometry.
  4. Set assist air first, then trim fluid pressure for edge definition.
  5. Spray a test panel and record settings for repeatable results.

Real Installation Tip: If tails appear, increase assist air in small steps before raising fluid pressure.

When to Rebuild / Replace

  • Fan narrows or edges fuzz at normal standoff distance.
  • Higher pressure required to maintain film build.
  • Pattern becomes asymmetric after checking guard/aircap alignment.
  • Frequent clogs despite correct filtration and viscosity.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (33-14413)OEM (Graco)
InterchangeListed replacement for GG4413Factory original GG4413
Pattern / Orifice8–10" fan; ~0.013" orifice8–10" fan; ~0.013" orifice
Use CaseCabinetry, furniture, light metal finishingCabinetry, furniture, light metal finishing
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution

FAQs

Approximately 8–10" fan with ~0.013" orifice on AAA guns, suitable for fine-finish applications.
Yes—this GG-series flat tip is specified for Graco G15/G40 manual guns and G40 automatic models where the IPL lists GG4413.
Bedford lists 33-14413 as the replacement for the OEM reference noted above.
Set assist air first for atomization, then fine-tune fluid pressure and maintain a consistent spray height for clean edges.
If available, orders ship from Bedford Precision Parts in Bedford Hill, NY using your selected carrier/service.