Graco GG4411 Spray Tip - Aftermarket Replacement | Bedford 33-1441

Air-assist airless flat tip for smooth edges and predictable film build on finish-grade work. This aftermarket tip mirrors OEM geometry for GG4411 and is listed by Bedford as 33-1441, delivering an ~8–10" fan with a 0.011" orifice for cabinetry, furniture, and light metal.

Aftermarket Fine-Finish AAA Industrial Duty

Why Choose This Spray Tip

  • ~8–10" flat fan supports even passes on doors, frames, and panels.
  • 0.011" orifice balances atomization with transfer efficiency.
  • Direct interchange with the OEM code for fast booth changeovers.

Colour cue: Guard/tip colour bands aid quick ID; exact shade may vary by lot.

Typical Compatibility

  • Graco G15 manual air-assist airless spray guns.
  • Graco G40 manual AAA spray guns.
  • Graco G40 automatic AAA guns used on fixtures and conveyors.
  • Any AAA package whose IPL specifies tip code “4411 / GG4411”.

Confirm by part number in your gun/system IPL before ordering.

What This Product Fits

  • Graco G15 air-assist airless spray guns.
  • Graco G40 manual AAA spray guns.
  • Graco G40 automatic AAA spray guns.

Sized for applications calling out GG4411 in the equipment IPL.

Technical Specifications

Aftermarket Bedford 33-1441
OEM Graco GG4411
FitsGraco G15/G40 AAA guns (manual & automatic) where GG4411 is specified
TypeAir-Assist Airless flat spray tip (fine-finish)
MaterialTungsten-carbide orifice with stainless components (typical AAA build)
FunctionProduces soft, even fan with crisp edges for controlled finish quality
PressureOperate within the gun/system’s rated working pressure
BrandAftermarket by Bedford Precision Parts; replaces Graco OEM

The “4411” code indicates a 40-series fan (~8–10") with a 0.011" orifice in the AAA family.

Installation Notes

  1. Relieve pressure and secure the work area.
  2. Inspect guard and aircap; clean with approved solvent.
  3. Insert tip with code facing forward; align fan with part geometry.
  4. Set assist air to smooth atomization, then trim fluid pressure.
  5. Spray a test panel and record settings for repeatability.

Real Installation Tip: If edges show faint tails, increase assist air slightly before raising fluid pressure.

When to Rebuild / Replace

  • Fan narrows or edges feather at normal standoff distance.
  • Higher pressure is needed to maintain target film build.
  • Off-center pattern after verifying guard/aircap alignment.
  • Frequent clogs despite correct filtration and viscosity.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (33-1441)OEM (Graco)
InterchangeIdentified replacement for GG4411Factory original GG4411
Pattern / Orifice~8–10" fan; 0.011" orifice~8–10" fan; 0.011" orifice
Use CaseCabinetry, furniture, light metal finishingCabinetry, furniture, light metal finishing
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution

FAQs

Approximately an 8–10" flat fan with a 0.011" orifice—ideal for fine-finish work on AAA guns.
Yes. GG-series tips are specified for Graco G15/G40 manual guns and G40 automatic models where the IPL lists GG4411.
Bedford catalogs 33-1441 as an aftermarket equivalent to the OEM GG4411 reference.
Dial in assist air first to refine atomization, then adjust fluid pressure. Maintain consistent spray height and filtration.
If available, orders ship from Bedford Precision Parts in Bedford Hill, NY using your selected carrier/service.