Graco GG4409 Spray Tip - Aftermarket Replacement | Bedford 33-14409

Air-assist airless flat tip for ultra-fine control on trim, cabinetry, and light metal parts. This aftermarket profile mirrors OEM geometry for GG4409 and is listed by Bedford as 33-14409, delivering an ~8–10" fan with a 0.009" orifice for delicate finish work.

Aftermarket Fine-Finish AAA Industrial Duty

Why Choose This Spray Tip

  • ~8–10" flat fan supports even passes on narrow rails and panels.
  • 0.009" orifice promotes smooth atomization with minimal build.
  • Direct interchange with the OEM code for quick booth changeovers.

Colour cue: Tip/guard colour bands assist fast ID at the gun; exact shade may vary by lot.

Typical Compatibility

  • Graco G15 manual air-assist airless spray guns.
  • Graco G40 manual AAA spray guns.
  • Graco G40 automatic AAA guns on fixtures and conveyors.
  • Any AAA package whose IPL specifies tip code “4409 / GG4409”.

Confirm by part number in your gun/system IPL before ordering.

What This Product Fits

  • Graco G15 air-assist airless guns.
  • Graco G40 manual AAA guns.
  • Graco G40 automatic AAA guns.

Sized for applications calling out GG4409 in the equipment IPL.

Technical Specifications

Aftermarket Bedford 33-14409
OEM Graco GG4409
FitsGraco G15/G40 AAA guns (manual & automatic) where GG4409 is specified
TypeAir-Assist Airless flat spray tip (fine-finish)
MaterialTungsten-carbide orifice with stainless components (typical AAA build)
FunctionProduces a soft, even fan with crisp edges for consistent finish quality
PressureOperate within the gun/system’s rated working pressure
BrandAftermarket by Bedford Precision Parts; replaces Graco OEM

The “4409” code indicates a 40-series fan (~8–10") with a 0.009" orifice in the AAA family.

Installation Notes

  1. Relieve pressure and secure the work area.
  2. Inspect guard and aircap; clean with approved solvent.
  3. Insert tip with code facing forward; align fan with part geometry.
  4. Set assist air to refine atomization, then trim fluid pressure.
  5. Spray a test panel and record settings for repeatable results.

Real Installation Tip: If edges show light tails, increase assist air slightly before raising fluid pressure.

When to Rebuild / Replace

  • Fan narrows or edges feather at normal standoff.
  • Rising pressure required to hold target film build.
  • Pattern pulls to one side after verifying guard/aircap alignment.
  • Frequent clogs despite correct filtration and viscosity.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (33-14409)OEM (Graco)
InterchangeIdentified replacement for GG4409Factory original GG4409
Pattern / Orifice~8–10" fan; 0.009" orifice~8–10" fan; 0.009" orifice
Use CaseTrim, cabinetry, furniture, light metal finishingTrim, cabinetry, furniture, light metal finishing
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution

FAQs

Approximately an 8–10" flat fan with a 0.009" orifice—ideal for ultra-fine finishing on AAA guns.
Yes. GG-series tips are specified for Graco G15/G40 manual guns and G40 automatic models where the IPL lists GG4409.
Bedford catalogs 33-14409 as an aftermarket equivalent to the OEM GG4409 reference.
Dial in assist air first to refine atomization, then adjust fluid pressure. Maintain consistent spray height and filtration.
If available, orders ship from Bedford Precision Parts in Bedford Hill, NY using your selected carrier/service.