Graco AAF614 Flat Tip - Aftermarket Replacement | Bedford 33-15614

Fine-finish air-assist airless tip for clean edges and consistent film build. This aftermarket tip replaces OEM AAF614 and is cataloged by Bedford as 33-15614, producing a 12–14" spray fan with an ~0.014" orifice ideal for cabinetry, furniture, and light metal finishing.

Aftermarket Pre-Orifice AAA Industrial Duty

Why Choose This Flat Tip

  • Pre-orifice design promotes soft atomization at moderate pressures.
  • 12–14" fan pattern supports even coverage on panels and doors.
  • Direct interchange with the OEM code for quick booth changeovers.

Colour cue: Tip/guard colour bands assist quick ID; exact shade may vary by lot.

Typical Compatibility

  • Graco G15 manual air-assist airless guns.
  • Graco G40 manual air-assist airless guns.
  • Graco G40 automatic AAA guns on fixed or conveyor fixtures.
  • Any AAA package whose IPL specifies flat tip “614 / AAF614”.

Confirm by part number in your gun/system IPL before ordering.

What This Product Fits

  • Graco G15 air-assist airless spray guns.
  • Graco G40 manual air-assist airless spray guns.
  • Graco G40 automatic air-assist airless spray guns used in production cells.

Listed by Bedford as the aftermarket replacement for the OEM tip indicated above.

Technical Specifications

Aftermarket Bedford 33-15614
OEM Graco AAF614
FitsGraco G15/G40 AAA guns (manual & automatic) where AAF614 is specified
TypeAir-Assist Airless flat spray tip (fine-finish, pre-orifice)
MaterialTungsten-carbide orifice with stainless components (typical AAA construction)
FunctionDelivers soft, even fan with crisp edges for controlled fine finishes
PressureOperate within gun/system rated working pressure
BrandAftermarket by Bedford Precision Parts; replaces Graco OEM

Tip code “614” denotes ~12–14" fan and ~0.014" orifice within the Graco fine-finish flat family.

Installation Notes

  1. Relieve system pressure and lock out the booth.
  2. Inspect guard and aircap; clean with approved solvent.
  3. Insert the tip with code facing forward; align fan to the part.
  4. Set assist air first for atomization, then trim fluid pressure.
  5. Spray a test panel and record pressure/air settings for repeatability.

Real Installation Tip: If faint tails appear, increase assist air slightly before raising fluid pressure.

When to Rebuild / Replace

  • Fan narrows or edges fuzz at normal standoff distance.
  • Increasing fluid pressure is needed to maintain target film build.
  • Off-center pattern after verifying guard/aircap alignment.
  • Frequent clogs despite correct filtration and material viscosity.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (33-15614)OEM (Graco)
InterchangeIdentified replacement for AAF614Factory original AAF614
Pattern / Orifice12–14" fan; ~0.014" orifice12–14" fan; 0.014" orifice
Use CaseCabinetry, furniture, light metal finishingCabinetry, furniture, light metal finishing
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution

FAQs

Approximately a 12–14" fan and ~0.014" orifice—well suited for fine-finish materials on AAA guns.
Yes. This AAF series flat tip is specified for Graco G15/G40 manual guns and G40 automatic models where the IPL lists AAF614.
Bedford lists 33-15614 as the aftermarket replacement for the OEM AAF614 reference.
Dial in assist air first to smooth atomization, then fine-tune fluid pressure. Maintain a consistent spray height and keep filters clean.
If available, orders ship from Bedford Precision Parts in Bedford Hill, NY using your selected carrier/service.