Graco 286319 Reversible Tip - Aftermarket Replacement | Bedford 33-7319-10

This aftermarket 319 SwitchTip lays down an approx. 6″ fan (first digit ×2) with a 0.019″ orifice for smooth, efficient coverage on walls, trim, and light exteriors. It is a direct alternative to OEM 286319 and mates with RAC 5 guards. Aftermarket reference: 33-7319-10.

Aftermarket Precision-Machined Industrial Duty

Why Choose This Reversible Tip

  • “319” code ≈ 6″ fan with a 0.019″ orifice - ideal for acrylic/latex paints, primers, and enamels.
  • Reverse-to-clean design clears clogs on the fly to minimize downtime.
  • Tungsten-carbide insert helps maintain pattern edge and extend service life.

Color cue: RAC 5 (RAC V) Hand-Tight Guard is typically Orange (e.g., 243161).

Typical Compatibility

  • Graco spray guns equipped with RAC 5 (RAC V) guards/holders (e.g., 243161).
  • Contractor PC, FTx, and Silver series guns using RAC 5 guards.
  • Graco electric & gas rigs that support 0.019″ tips (verify your model’s max tip size).

Always confirm your sprayer’s maximum tip size and working pressure before use.

What This Tip Fits

  • RAC 5 (RAC V) tip guards/holders on compatible Graco spray guns and sprayers.
  • Common rigs that ship with or accept RAC 5: Classic/Pro/Ultra Max II series, Ultra handhelds (with RAC 5 adapters), many GMax & GH series guns (see manual).
  • Applications: acrylic/latex wall paints, primers, and enamels where a 0.019″ orifice and ~6″ fan are recommended.

Technical Specifications

Aftermarket Bedford 33-7319-10 (10-Pack)
OEM 286319
FitsRAC 5 (RAC V) guard/holder (e.g., Orange Hand-Tight Guard 243161)
TypeReversible airless spray tip (319)
MaterialTungsten-carbide orifice; steel stem; polymer handle
FunctionApprox. 6″ fan; 0.019″ orifice; reverse to clear clogs
PressureUse only within your gun/sprayer rated working pressure
BrandBedford Precision Parts (Aftermarket)

Tip code guide: first digit × 2 ≈ fan width in inches (@ ~12″); last two digits = orifice size in thousandths of an inch.

Installation Notes

  1. Relieve sprayer pressure; engage the gun trigger lock.
  2. Insert the 319 tip into the RAC 5 guard with the arrow pointing forward.
  3. Hand-tighten the guard; ensure the tip seal is correctly seated.
  4. Test at low pressure; increase until the fan is even with no tails.
  5. To clear a clog, rotate 180°, trigger briefly, then return to spray position.

Pro tip: Match gun filter mesh to coating viscosity and strain materials to extend tip life.

When to Rebuild / Replace

  • Persistent tails or uneven edges despite correct pressure.
  • Requires unusually high pressure to maintain pattern.
  • Fan width drifts far from the expected ~6″ for a 319 tip.
  • Visible wear or out-of-round at the carbide orifice.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (33-7319-10)OEM (Graco)
Fit & InterfaceMatches RAC 5 (RAC V) guard interfaceFactory RAC 5 SwitchTip interface
Performance~6″ fan; 0.019″ orifice for balanced coverageFactory-spec fan/orifice geometry
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution
ValueLower cost of ownershipOEM brand program

FAQs

Yes. This aftermarket 10-pack matches RAC 5 fit and reversible operation with comparable spray geometry.
RAC 5 (RAC V) guards such as the Orange Hand-Tight Guard (e.g., 243161). Confirm your gun/guard model.
Acrylic/latex paints, primers, and enamels—always verify coating TDS and your sprayer’s max tip size.
Rotate to the clean position, trigger briefly to purge, then rotate back to spray. Maintain filters and strain materials to reduce clogs.
If in stock, orders ship from Bedford Precision Parts in Bedford Hill, NY via your selected carrier/service.