Shopping cart
Your Cart is empty
Graco 25D258 Repair Kit - Aftermarket | Bedford 20-3406
PriceQuantity
$ 263.26
Part #:
25D258
MPN:20-3406
Manufacturer:Bedford Precision Parts
Guaranteed safe & secure checkout
In Stock
Graco 25D258 Kit - Aftermarket | Bedford 20-3406
Renew sealing integrity and restore steady output with a complete service set for qualifying industrial fluid sections. This aftermarket kit directly replaces Graco 25D258 and is supplied as Bedford 20-3406, helping reduce downtime and stabilize pressure for consistent atomization.
Aftermarket Value
Precision-Machined
Industrial Duty
Why Choose This Repair Kit
- Replaces wear components and packings to stop weeping and bypass.
- Engineered seal materials resist common solvents and abrasives.
- Direct-fit sequence speeds service using OEM torque specifications.
- Helps maintain uniform spray pattern and target film build.
Typical Compatibility
- Graco Xtreme airless lowers listed for this kit in the IPL.
- XP plural-component rigs built with the same wet ends.
- XM systems using compatible fluid sections per model IPL.
Confirm by Illustrated Parts List (IPL) for your exact pump ratio and lower assembly.
What It Fits
- Designated Graco Xtreme fluid sections that call out the OEM number shown above.
- XP and XM proportioners utilizing those lowers (verify by IPL callout).
- Factory airless packages sharing the same lower assemblies noted in the IPL.
If your parts list references the OEM shown here, Bedford 20-3406 is the correct direct-fit aftermarket match.
Technical Specifications
| Aftermarket # | Bedford 20-3406 |
|---|---|
| OEM # | Graco 25D258 |
| Fits | Specified Graco Xtreme lowers; select XP/XM rigs per IPL |
| Type | Packing & wear component repair kit |
| Material | Engineered polymers, TFE elements, wear-resistant seats |
| Function | Restores sealing, reduces pulsation, improves spray consistency |
| Pressure | For high-pressure airless systems (use pump’s rated working pressure) |
| Brand | Bedford Precision Parts (Aftermarket) |
Installation Notes
- Relieve system pressure; lock out air/hydraulic supply and flush per OEM procedure.
- Remove the lower from the drive and secure in a soft-jaw vise.
- Disassemble the fluid section; clean all parts and inspect for scoring or corrosion.
- Pre-lube seals; install components in the exact IPL sequence/orientation.
- Reassemble to torque spec, prime with compatible fluid, and leak-test before production.
Real Installation Tip: A light polish of minor bore glazing (if allowed by OEM) can help the new packing bed in evenly.
When to Rebuild / Replace
- Visible fluid at the packing nut or wet cup.
- Erratic pressure or flutter at the gun.
- Reduced output requiring higher stroke rate.
- Air entrainment or contamination in the fluid stream.
Bedford vs OEM
| Feature | Bedford Aftermarket | OEM (Graco) |
|---|---|---|
| Fit & Function | Direct replacement per IPL | Original factory configuration |
| Material Set | Durable polymer/TFE sealing stack | Factory material specification |
| Service Life | Industrial-duty construction | OEM baseline |
| Availability | If in stock, ships from Bedford Precision Parts in Bedford Hill, New York. | Ships via OEM distribution |
Frequently Asked Questions
Check your Illustrated Parts List. If the parts list for your lower references the OEM number shown above, Bedford 20-3406 is the correct aftermarket kit.
It contains sealing and wear components for the specified fluid section. Reuse metallic hardware if within spec; replace any damaged pieces during service.
Yes. New packings reduce bypass and pressure fluctuations, producing a more uniform spray pattern and consistent film build.
Standard hand tools, a soft-jaw vise, torque wrench, and seal picks are recommended. Follow OEM torque values and safety procedures.
If in stock, orders ship from Bedford Hill, New York for fast turnaround.
