Graco 24F268 Intake Seat Kit - Aftermarket Replacement | Bedford 20-3542

Restore suction and reduce bypass at the pump inlet with this intake seat repair set. The kit replaces Graco 24F268 and is cross-referenced by Bedford Precision as 20-3542, providing the critical seat components for popular contractor sprayers.

Aftermarket Precision-Machined Industrial Duty

Why Choose This Intake Seat Kit

  • Carbide seat construction for long service life in demanding coatings.
  • Drop-in aftermarket alternative mapped directly to the OEM number for quick bench rebuilds.
  • Supports consistent priming and steady feed to the gun after service.

Service cue: Always flush and clean the lower assembly before installing the new seat to avoid embedding particles on first start-up.

Typical Compatibility

  • Graco Ultra Max II 490, 495, 595 airless sprayers where the IPL calls out the intake seat kit.
  • Other sprayers that specify the kit under the OEM reference shown below (also appears as 24F-268 in some listings).

Always verify your sprayer’s Illustrated Parts List before ordering.

What This Product Fits

  • Ultra Max II 490 (select model numbers 249911/249913/249914 series and later, per parts lists).
  • Ultra Max II 495 (249915/249916/249917 series).
  • Ultra Max II 595 (249918/249919 series).
  • Any unit whose IPL explicitly specifies intake seat kit 24F268 (or 24F-268).

Bedford cross-reference confirms replacement for the OEM kit under the numbers shown below.

Technical Specifications

Aftermarket Bedford 20-3542
OEM 24F268 (Intake Seat Kit; sometimes shown as 24F-268).
FitsGraco Ultra Max II 490/495/595 and other sprayers listing the kit in their IPL.
TypeIntake (inlet) seat repair kit for pump lower
MaterialCarbide seat components for abrasion resistance.
FunctionRestores sealing at the inlet check to maintain prime and stable flow.
PressureUse within sprayer rating; Ultra/Ultra Max II families list up to ~3300 psi working pressure.
BrandBedford Precision Parts (Aftermarket)

System limits are set by the lowest-rated component on your sprayer.

Installation Notes

  1. Relieve pressure; lock the gun trigger and disconnect power/air per your manual.
  2. Remove the pump lower; document orientation of the intake hardware during teardown.
  3. Clean the cavity and threads; inspect the ball, cage, and seals for wear or scoring.
  4. Install the new intake seat components; apply light thread/seal lubricant where specified.
  5. Reassemble, prime with compatible fluid, then leak-test and verify pattern at low pressure.

Tip: If the seat shows pitting or the check ball is out-of-round, replace both at the same time for consistent sealing.

When to Rebuild / Replace

  • Loss of prime or cavitation noise at the pump inlet.
  • Drips from the inlet or visible bypass after purging air.
  • Erratic pressure at normal tip sizes despite clean strainers.
  • Seat wear, pitting, or contamination observed during inspection.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (20-3542)OEM (Graco)
Fit & InterfaceMatches intake seat stack noted in the IPLFactory intake seat kit 24F268
MaterialsCarbide seat components for wear resistanceOEM-specified seat components
Working PressureUsed within sprayer’s published rating (e.g., ~3300 psi on many Ultra Max II units)Defined by each model’s technical data
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution
ValueCost-effective service solutionOEM program

Cross-reference and material details verified from distributor listings and Graco service literature.

FAQs

Yes. Bedford 20-3542 is an aftermarket alternative for the intake seat kit referenced as Graco 24F268 (sometimes shown as 24F-268). :contentReference[oaicite:17]{index=17}
Ultra Max II 490/495/595 and other models whose Illustrated Parts List calls out 24F268. Always match by your exact model and series. :contentReference[oaicite:18]{index=18}
The kit features carbide seat components for durability in pump inlet service. :contentReference[oaicite:19]{index=19}
Use within your sprayer’s rating. Ultra/Ultra Max II platforms typically list up to ~3300 psi working pressure. :contentReference[oaicite:20]{index=20}
If available, orders ship from Bedford Precision Parts in Bedford Hill, NY using your chosen carrier/service.