Graco 245797 Hose Assembly - Aftermarket Replacement | Bedford 13-3226

Keep your LineLazer pump outlet flexible and responsive with this 3/8 in. x 3 ft whip line. It is an aftermarket alternative to Graco 245797 and cross-referenced by Bedford as 13-3226, built for stable flow and reduced operator fatigue on parking lot stripers.

Aftermarket Precision-Machined Industrial Duty

Why Choose This Hose Assembly

  • 3/8 in. I.D. x 3 ft length for smooth gun handling at the cart.
  • Rated to approximately 3300 PSI to match LineLazer duty cycles.
  • Short whip reduces pulsation at the gun and eases operator movement.

Service note: Always inspect ends and cover for abrasion before each shift; replace at the first sign of blistering or braid exposure.

Typical Compatibility

  • LineLazer III, IV, and V stripers (whip hose at the gun manifold).
  • LineLazer III parts lists for Models 233688 & 233690 (ref. hose at pump outlet).
  • Commonly specified on LineLazer 3900 and 5900 series units.

Confirm your model and parts list to ensure the hose length and thread style meet your setup.

What This Product Fits

  • Graco LineLazer III Models 233688 & 233690 (OEM callout for 3/8 in. x 3 ft hose).
  • LineLazer 3900 and 5900 applications that specify the same whip hose length.
  • General LineLazer III/IV/V gun whip locations where 3 ft whip is required.

If your unit uses a different length or end style, select the hose listed in your machine’s exact IPL.

Technical Specifications

Aftermarket Bedford 13-3226
OEM 245797
FitsLineLazer III/IV/V (see specific model IPL); LineLazer III Models 233688 & 233690
TypeWhip Hose Assembly, pump outlet to spray gun manifold
MaterialSynthetic cover with braided reinforcement; crimped ends
FunctionImprove handling at the gun, dampen pulsation, and maintain flow
PressureApprox. 3300 PSI working (apply your sprayer’s system rating)
BrandBedford Precision Parts (Aftermarket)
Dimensions3/8 in. I.D. × 3 ft length

Do not exceed the lower of system or hose ratings. Replace hose assemblies on an interval consistent with site conditions.

Installation Notes

  1. Relieve system pressure and close the fuel/air source as applicable.
  2. Remove the old whip from the manifold and gun swivel; capture any seals.
  3. Inspect threads and seats; replace O-rings/seals where specified.
  4. Install the new whip hose; torque to spec and avoid twist in the line.
  5. Pressurize, leak-check with mild soap solution, and test spray pattern.

Tip: Use a short test line first; route the whip to avoid tire and frame rub points.

When to Rebuild / Replace

  • Cover cuts, kinks, blisters, or exposed braid.
  • Fitting leaks that persist after re-torque with new seals.
  • Stiff or memory-set hose that restricts gun motion.
  • Any hose that has reached manufacturer’s service life under heavy use.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (13-3226)OEM (Graco)
Fit & InterfaceCross-referenced to OEM hose dimensions and endsFactory hose length and interface
Working PressureApprox. 3300 PSI (application dependent)Listed per model IPL/spec
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution
ValueBudget-friendly alternativeOEM program

FAQs

Yes. 13-3226 is listed as an aftermarket replacement for the OEM hose assembly 245797 used on LineLazer applications.
LineLazer III, IV, and V families, including specific LineLazer III Models 233688 and 233690 where the 3/8 in. × 3 ft hose is called out in the IPL.
The whip hose is commonly listed at about 3300 PSI. Always follow the lower rated value between your sprayer and installed hose.
Relieve pressure, replace worn seals, avoid twisting during install, torque to spec, and perform a leak check before painting.
If available, orders ship from Bedford Precision Parts in Bedford Hill, NY using your selected service.