Graco 244895 Teflon O-Rings - Aftermarket Replacement | Bedford 55-2536

Keep outlet filter caps sealing as intended with these PTFE service rings supplied in a convenient 10-pack. The set replaces Graco 244895 and is provided as Bedford 55-2536, supporting routine maintenance on select Graco pump/filter assemblies that specify this size. PTFE (Teflon) resists chemicals and cold flow better than many elastomers, helping maintain stable pressure and finish quality after rebuilds. Use when the Illustrated Parts List calls out this repair pack for the filter cap location.

Aftermarket PTFE Material Industrial Duty

Why Choose These O-Rings

  • Direct aftermarket cross for the OEM pack called out in filter cap service.
  • PTFE composition supports chemical resistance and dimensional stability.
  • 10-pack quantity covers immediate repair plus spares for shop inventory.

Color: Natural off-white PTFE.

Typical Compatibility

  • Graco outlet filter cap locations that specify this PTFE ring in the IPL.
  • Common on heavy-duty and Xtreme-series pump filter assemblies using lower-cap seals.
  • Aftermarket repair programs that reference the Bedford cross number below.

Always confirm the exact OEM reference and series letter for your unit before ordering.

What This Product Fits

  • Graco outlet filter assemblies where the lower cap O-ring is listed as OEM 244895 (a.k.a. 244-895) in the parts list.
  • Graco Xtreme pump families that identify this ring at the lower filter cap position in quick-reference charts.
  • Service kits and distributor BOMs that designate the PTFE ring replacement for the cap location noted above.

If your manual specifies a different ring (e.g., upper-cap size or elastomer variant), select that exact reference.

Technical Specifications

Aftermarket Bedford 55-2536 (10-pack)
OEM Graco 244895 (PTFE O-rings)
FitsOutlet filter cap location on select Graco pumps; verify IPL and series
TypePTFE O-ring set for filter cap sealing
MaterialVirgin PTFE (Teflon)
FunctionSeals filter cap interface to maintain pressure and reduce seepage
PressureFollows system/assembly rating; ring itself is non-rated
BrandBedford Precision Parts (Aftermarket)

Inspect filter core, caps and threads; replace upper-cap ring and related seals if noted in your model’s chart.

Installation Notes

  1. Relieve pressure and isolate the sprayer; remove the outlet filter assembly.
  2. Disassemble cap(s); clean the bore and seating lands thoroughly.
  3. Lightly lubricate the new PTFE ring with compatible fluid if permitted by the manual.
  4. Install squarely without twisting; seat the cap and tighten to specification.
  5. Re-pressurize and check for weeping at operating pressure and temperature.

Tip: Replace upper-cap and lower-cap rings together to stabilize sealing after service.

When to Rebuild / Replace

  • Filter cap seepage after tightening or recurring weeping during spray.
  • Flattened, nicked or chemically etched rings on teardown.
  • Pressure fluctuation tied to air ingestion at the filter interface.
  • Service interval reached per the pump or filter maintenance chart.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (55-2536)OEM (Graco)
Fit & InterfaceCross-referenced to the OEM pack for the noted cap locationFactory PTFE ring per IPL
PerformancePTFE rings for chemical and temperature stabilityOEM PTFE rings as specified
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution
ValueCost-efficient service optionOEM program

FAQs

Yes. Bedford lists 55-2536 as the replacement for the OEM reference shown in the specifications.
At the outlet filter cap location on select Graco pumps where the IPL calls out this PTFE ring set (lower-cap position on many heavy-duty/Xtreme assemblies).
Ten (10) rings, providing coverage for immediate repair and spare stock.
Inspect the filter core, upper-cap seal, and caps. Replace companion rings and worn parts as your model chart recommends.