Graco 238562 Fine Tip Filter - Aftermarket Replacement | Bedford 55-2455

Fine 100-mesh tip filtration that helps prevent clogs and surface defects right at the spray tip. This aftermarket element replaces the OEM tip filter and installs inside the dripless tip-guard adapter for last-chance filtration. OEM ref: 238562; Aftermarket ref: 55-2455.

Aftermarket Precision-Machined Industrial Duty

Why Choose This Tip Filter

  • 100-mesh screen helps reduce streaks and tails caused by contaminants.
  • Installs at the tip guard for cleaner, more consistent spray patterns.
  • Aftermarket value with dependable seating and repeatable fit.

Service note: Replace after heavy primer use or when switching to fine finishes to maintain pattern quality.

Typical Compatibility

  • Graco PerformAA 50 air-assisted gun (100-mesh tip filter pack).
  • Systems using the Graco dripless tip-guard adapter (filter sits inside the adapter).
  • Assemblies listed “For Use With” 20L037, 20L038, 20L039, 20L040, 20L041.

Always confirm against your sprayer/gun IPL and tip guard part before ordering.

What This Product Fits

  • Graco PerformAA 50 gun models specifying 100-mesh tip filters.
  • Graco guns outfitted with the dripless RAC tip-guard adapter.
  • Graco SKU references: 20L037, 20L038, 20L039, 20L040, 20L041 (where a 100-mesh tip filter is called out).

If unsure, provide your gun/tip-guard numbers and we’ll verify fitment.

Technical Specifications

Aftermarket #Bedford 55-2455 (25-pack, fine, enamel)
OEM #Graco 238562 (100-mesh tip filter)
FitsPerformAA 50; dripless tip-guard adapter systems; assemblies 20L037–20L041 (as specified)
TypeFine tip filter (last-chance filtration at tip guard)
MaterialMetal mesh screen with formed carrier
FunctionCaptures particles before the spray tip to limit clogs and pattern defects
PressureUse within the spray gun/tip-guard rated working pressure
BrandAftermarket by Bedford; crosses to Graco OEM

Pack quantity commonly supplied as 25. Replace sooner when spraying high-solids materials.

Installation Notes

  1. Relieve system pressure; engage trigger lock and disconnect supply.
  2. Remove the RAC tip and tip guard from the spray gun.
  3. Insert the 100-mesh tip filter into the dripless tip-guard adapter (screen centered).
  4. Reinstall tip and guard; hand-tighten, then secure per tool spec.
  5. Test with compatible fluid; confirm no leaks and stable fan pattern.

Real installation tip: Keep a clean spare in your pouch; swap when pattern fades rather than forcing higher pressure.

When to Rebuild / Replace

  • Frequent tip clogs despite clean material and strainers.
  • Uneven fan or tails at the edges of the pattern.
  • Visible dents, frays, or collapsed screen.
  • Color carry-over after changing coatings.

Bedford vs OEM Comparison

FeatureBedford AftermarketOEM (Graco)
Mesh Rating100-mesh fine (55-2455)100-mesh fine (238562)
Install LocationInside dripless tip-guard adapterInside dripless tip-guard adapter
Pack Quantity25 per pack25 per pack
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution

FAQs

Yes. Bedford 55-2455 is an aftermarket alternative for the OEM 238562 100-mesh tip filter and fits the same adapter location.
Typical use on Graco PerformAA 50 guns and on guns that use the dripless RAC tip-guard adapter. It’s also listed “For Use With” assemblies 20L037–20L041. Check your IPL to confirm.
Inside the dripless tip-guard adapter, directly upstream of the spray tip for last-chance filtration.
Replace when switching from primers to fine finishes, after noticeable pressure increases, or any time the fan pattern shows tails or spitting.
Commonly supplied as a 25-pack for shop and field maintenance.