Shopping cart
Your Cart is empty
Graco 215496 Bull (Teflon) Repair Kit Aftermarket | Bedford 20-1181
PriceQuantity
$ 169.76
Part #:
215496
MPN:20-1181
Manufacturer:Bedford Precision Parts
Guaranteed safe & secure checkout
In Stock
Graco 215496 Bull (Teflon) Repair Kit - Aftermarket Replacement | Bedford 20-1181
Restore pump performance and finish quality with a precision-matched rebuild that renews the seal stack and wear surfaces in qualifying industrial fluid sections. This kit mirrors the fit and function of Graco 215496 and is supplied as Bedford 20-1181 for dependable, cost-effective maintenance.
Aftermarket Value
Precision-Machined
Industrial Duty
Why Choose This Repair Kit
- Replaces critical packings and wear items to stop weeping and bypass.
- Engineered polymers and TFE elements resist solvents and abrasion.
- Direct-fit sequence for quick, repeatable service with OEM torque values.
- Helps stabilize pressure for consistent atomization and uniform film build.
Typical Compatibility
- Selected Graco industrial wet ends that specify this kit in the IPL.
- XP and XM plural-component rigs built around those lowers.
- Factory airless packages sharing the same designated fluid sections.
Always verify by Illustrated Parts List (IPL) for your exact model/ratio before ordering.
What It Fits
- Graco Xtreme fluid sections that call out the OEM number shown on this page.
- Compatible XP Proportioners using those Xtreme wet ends (per IPL callout).
- XM Plural-Component Systems equipped with the same lowers (per IPL).
If your pump IPL references the OEM above, Bedford 20-1181 is the correct aftermarket match.
Technical Specifications
| Aftermarket | Bedford 20-1181 |
|---|---|
| OEM | Graco 215496 |
| Also Replaces | Graco 45-1 King GH733, 20-1 Bull |
| Fits | Designated Graco Xtreme lowers; select XP/XM rigs per IPL |
| Type | Packing & wear component repair kit |
| Material | Engineered polymer/TFE seals, wear-resistant elements |
| Function | Restores sealing integrity, reduces pulsation, improves spray uniformity |
| Pressure | For high-pressure airless systems (use sprayer’s rated working pressure) |
| Brand | Bedford Precision Parts (Aftermarket) |
Installation Notes
- Relieve all pressure; lock out air/hydraulic supply and flush per OEM procedure.
- Remove the lower from the drive; secure in a soft-jaw vise.
- Disassemble fluid section; clean parts and inspect for scoring/corrosion.
- Pre-lube new packings; install in the exact sequence/orientation shown in the IPL.
- Reassemble to torque spec, prime with compatible fluid, and leak-test.
Real Installation Tip: Lightly warm stubborn seats (if allowed) to ease removal without gouging the bore.
When to Rebuild / Replace
- Product weeping at the packing nut or fluid in the wet cup.
- Erratic pressure, pulsation, or flutter at the gun.
- Reduced output requiring higher stroke rate to maintain flow.
- Air entrainment or visible contamination in the fluid stream.
Bedford vs OEM
| Feature | Bedford Aftermarket | OEM (Graco) |
|---|---|---|
| Fit & Function | Direct replacement per IPL | Original factory configuration |
| Material Set | Durable polymer/TFE sealing stack | Factory material specification |
| Service Life | Industrial-duty construction | OEM baseline |
| Availability | If in stock, ships from Bedford Precision Parts in Bedford Hill, New York. | Ships via OEM distribution |
Frequently Asked Questions
Check your pump’s Illustrated Parts List. If the OEM number shown here appears for your wet end, Bedford 20-1181 is the correct aftermarket kit.
It includes sealing and wear components for the specified fluid section. Reuse metallic hardware if within spec; replace anything damaged or scored.
Yes. New packings reduce bypass and stabilize pressure, yielding a more consistent spray pattern and film build.
Standard hand tools, soft-jaw vise, torque wrench, and seal picks are recommended. Follow OEM torque values and safety procedures.
If in stock, orders ship from Bedford Hill, New York for fast turnaround.
