Graco 207386 President Repacking Kit - Aftermarket Replacement | Bedford 20-1351

Restore seal integrity and stable output on Graco pneumatic “President” pump lowers that specify OEM 207386. This Bedford alternative (20-1351) refreshes the fluid section to recover prime, reduce leakage, and maintain consistent pressure.

Aftermarket Precision-Machined Industrial Duty

Why Choose This Repacking Kit

  • Rebuilds worn packing stacks to eliminate weeping and pressure loss.
  • Material selection aimed for long wear with common industrial coatings.
  • Aftermarket value with consistent Bedford quality and sizing control.

Color cue: follow your service manual’s Green lubrication and seal orientation guidance during assembly.

Typical Compatibility

  • Graco air-operated “President” pump lowers used in finishing and transfer systems.
  • Industrial rigs feeding air-assisted airless or conventional spray guns within rated pressure.
  • Architectural primers/latex and many industrial topcoats (confirm chemistry vs. seal materials).

Always confirm by part-number callout in your pump’s official exploded view/BOM.

What This Product Fits

  • Graco “President” series pneumatic pumps whose parts manuals list 207386 as the repacking (packing) kit.
  • Common in circulation on plant/booth feed systems and pressure-feed spray packages using President lowers.
  • Not intended for handheld or small contractor electric sprayers; this kit services professional fluid sections.

. Share your exact pump model to verify fitment prior to shipment.

Technical Specifications

Aftermarket Bedford 20-1351
OEM 207386
FitsGraco President pump lowers that specify 207386 in the official parts list/BOM
TypeRepacking / packing kit (fluid section seals & wear components)
MaterialMixed polymer packings, elastomers, and corrosion-resistant hardware (per application)
FunctionRestores sealing surfaces to recover prime, pressure holding, and pattern stability
PressureUse within the rated working pressure of your specific pump lower/system
BrandBedford Precision Parts (Aftermarket)

Match by OEM number first. If your manual shows supersedes/alternates for 207386, use the latest callout.

Installation Notes

  1. Isolate air supply, depressurize system, and lock out per site safety policy.
  2. Remove the pump lower; document existing packing order and cup orientation.
  3. Clean metal parts; inspect rod/cylinder for scoring or pitting and replace if needed.
  4. Lubricate new packings; install in the exact sequence from the service diagram.
  5. Reassemble, purge air, then test at low pressure before returning to production.

Pro tip: If leakage persists after rebuild, check rod finish and ball/seat condition—they directly affect packing life.

When to Rebuild / Replace

  • Weeping at the throat or loss of prime under normal conditions.
  • Pressure creep at the gun with the trigger closed.
  • Need for unusually high pressure to maintain pattern (with a known-good tip).
  • Inspection reveals contamination, flattened cups, or scoring.

Bedford vs OEM Comparison

FeatureBedford Aftermarket (20-1351)OEM (Graco)
Fit & InterfaceBuilt to the OEM 207386 packing stack geometryFactory 207386 specification
PerformanceIndustrial sealing focused on uptime and consistencyFactory material set and tolerances
AvailabilityIf in stock, ships from Bedford Precision Parts in Bedford Hill, New York.Ships via Graco distribution
ValueLower cost of ownershipOEM brand program

FAQs

Yes. It is an aftermarket repacking kit built to the OEM 207386 dimensions and sequence for the applicable President pump lowers.
Open your pump’s parts manual and confirm that “207386” appears in the fluid section BOM. If listed, 20-1351 is the correct aftermarket alternative.
Compatibility depends on the packing chemistry and your coating’s solvent/abrasive content. For aggressive materials, verify seal materials against the coating TDS.
Inspect the piston rod finish, cylinder wall, ball/seat, and throat wiper. Worn hard parts can prematurely damage fresh packings.
If in stock, orders ship from Bedford Precision Parts in Bedford Hill, NY using your selected service.